Consumers who recently purchased the Orthall R2016 fingerprint lock fingerprint lock will not be installed after taking the product home. Of course there will be professional installers who will install the fingerprint lock. However, in order to appear unnecessary trouble and consumers who have relatively strong ability to collect, we simply introduce some of his installation methods for everyone, which can play a role in enveloping. So let's take a look at the specific Orsole R2016 smart fingerprint lock installation steps!
R2016 smart fingerprint lock, determine the door to open:
When we are installing, we must determine the direction of opening. Most of them are now open to the right. Here we also use this list. Of course, small partners can also choose other directions.
R2016 smart fingerprint lock II, lock body installation:
1. Make sure the direction of the lock tongue is consistent with the door opening direction. If it is not, the 6068 anti-theft lock body used in the Morrison fingerprint lock can be adjusted. Use a screwdriver to push the latch bolt up. After rotating 180°, loosen the screwdriver to reset it.
2. Then put the lock body into the opened door hole with the beveled end as the upper end, let the lock body line pass out of the front door hole from the upper end door hole, and then use the screw to lock the lock body.
3. Put the lock cylinder into the lock body hole from the outside of the door, and fix the lock cylinder with the lock screw. At this time, the lock body is completely installed. Use the mechanical key to test whether the lock body tongue is working properly, and then install the panel. .
R2016 smart fingerprint lock three, panel installation:
1. Before installing the panel, press the door to open the handle and keep the front and back panels parallel to the door. Do not skew the left and right distances so that the handle is aligned with the horizontal direction of the lock body. Adjust the vertical distance so that the vertical direction of the handle is consistent with the lock body.
2. First put the front rod into the lock body hole from the outside, and then insert the lock body line into the panel bus line, and the public line through the door hole to the back of the door, then put the square spring into the handle hole Align the front panel handle hole with the front rod, then install the back panel from the inside of the door and fix the back panel and front panel to the door with screws.
3. Then put the rear rod into the square hole of the lock body from the inside of the door, put the spring into the handle hole of the rear panel, and plug the connection line of the rear panel with the public line of the front panel.
4. Insert the excess wire into the entry hole, and then place the front panel on the back lever and secure it with the screw.
5. Then insert a four-section No. 5 alkaline battery to test the entire lock installation and function.
R2016 smart fingerprint lock four, buckle box buckle plate installation:
1. After the fingerprint lock test is normal, the buckle box and the buckle plate can be installed on the door frame. Note the direction of the lower end of the buckle plate, and the square hole is at the upper end.
2. Then open and close the door to check whether the closing of the button box and the bolt door frame is normal. Note that it is best to have someone inside and outside the door to prevent the door from opening during testing. This completes our door lock installation.
R2016 smart fingerprint lock fingerprint lock installation considerations
R16 smart fingerprint lock fingerprint lock is often caused by improper installation, so let's take everyone to understand the issues that need attention in the installation process.
1) Because the door opening method is not the same, the holes on the mounting mold are not the same, so be sure to determine the correct position before installation.
2) Lock front and rear body wires, sockets and plugs to ensure the correct connection.
3) Before installation, determine the installation height. Place the mounting module in the appropriate position and use a pencil to draw the position of the hole.
4) When the hole is drawn, the flange of the mounting mold must be perpendicular to the door frame. Otherwise, the lock body cannot be installed perpendicular to the door.
5) The lock core is generally required to be installed in the middle of the door thickness.
6) After opening the hole in the door frame, be sure to clean the wood chips or other foreign objects inside the hole to prevent the door from dropping the debris into the lock body when the switch is vibrating.
R2016 smart fingerprint lock summary: Through the above installation methods and precautions, we also simply understand the fingerprint lock installation, fingerprint lock installation is actually a very important process, generally more than 80% of our fingerprint lock failure is due to the installation Due to some negligence, we must standardize the installation procedure during the installation process and pay attention to the installation considerations mentioned above.
related suggestion:
A: How to change the password with a password lock?
Recommended: face recognition electronic lock face recognition smart lock smart lock market
0
Anfeng Magnets Manufactruing Co.,Ltd , https://www.anfengmagnetics.com