The magic of drilling machine

I. Cutting plexiglass on the drilling machine There are two pieces of plexiglass plate on the panel of the electronic digital display speed measuring instrument produced by our factory. It used to be a special cutting knife for the fitter grinding, with the ruler leaning against the cut, the trimming is not uniform, the size Different, it still needs to be repaired, which takes time and effort. After the change, the sawing machine is cut with a saw blade milling cutter. The cutting piece takes only one minute on average, and the trimming edges are neat and uniform in size. Its structure is shown in Figure 1.

9500 Lbs Electric Winch

Off-road driving with your vehicle can be exhilarating, but sometimes you might find yourself stuck on some rocks or in a pit of mud. Fortunately, if you have a winch mounted on your vehicle, you shouldn`t have any problem getting yourself unstuck. To use your 12 volt winch properly, you`ll need to locate a sturdy anchor to attach it to. Once your winch is rigged, you can slowly pull your vehicle out from whatever it`s stuck in.

9500LBS Line Speed And Amp Draw(First Layer)

9500LBS Line Speed And Amp Draw(First Layer)

Line Pull

lb

No

4000

6000

8000

9500

kg

LOAD

1818

2727

3636

4318

Line Speed

ft/min

33.50

14.07

12.60

10.10

8.20

m/min

11.74

4.29

3.84

3.08

2.5

Motor Current

Amps

72

143

201

276

353

9500LBS Line Speed And Amp Draw(First Layer)

Layer of Cable

1

2

3

4

Rated Line Pull per Layer

lb

9500

8000

6000

5000

kg

4318

3636

2727

2273

Length of Cable on Drum

ft

16.50

41.66

64.19

75.44

m

5.03

12.7

19.57

23

Typical Applications: off-road vehicles, agricultural vehicles, ATV all-terrain vehicles, yachts, fire rescue vehicles, road barrier vehicles and other special vehicles, special vehicles.

Usages:


Plug the winch remote control into the winch.
Your winch should have come with a remote control attached to a long cord. Look for the plug at the end of the cord and attach it to the corresponding receptacle on the outside of the winch. Run the remote control cord from the winch to the driver`s seat and place the remote control in your vehicle

Put on a pair of thick gloves. Never handle a winch cable without gloves on. The cable could cut your hands.


Find something in front of your car to anchor your winch to.
A large tree trunk, boulder, or other vehicle is ideal. Don`t anchor your winch to something small and weak or you risk breaking it. Try to find an anchor that`s straight in front of your vehicle.


Use the disengage lever to release the winch cable.
The disengage lever should be located on the outside of the winch. The lever should have an option that says [free spool" or [disengaged." Turn the lever to that option. This will release the cable so you`re able to manually pull it out from the winch.


Pull the winch cable all the way to the anchor.
Don't pull too much of the cable out or you'll create unnecessary slack. Set the end of the cable down next to the anchor.

If the winch cable doesn't reach the anchor, look for another anchor that's closer to your vehicle.

Wrap a tree trunk protector around the bottom of the anchor. A tree trunk protector is a thick nylon strap with two loops, one on each end. Wrap the protector around the anchor so the two end loops are facing you. Hold the two end loops in your hand.

If your winch didn`t come with a tree trunk protector, you can order one online or find one at your local hardware store.

Hook a D-shackle through the 2 loops on the protector. A D-shackle is a curved shackle with a large pin that screws in and out of the shackle. Remove the pin from the D-shackle and put the curved part of the D-shackle through both of the loops on the tree trunk protector. Once the loops are on the shackle, reinsert the pin and twist it to tighten it into place.


Hook the winch hook to the D-shackle with the tip facing up.
The winch hook is the hook at the end of the winch cable

Turn the disengage lever back to [engaged." You want the lever to be back in the position it started in before you released the winch cable. This will prevent more cable from coming out of the winch.

Use the winch remote to slowly pull the winch cable taut. Press the button on the remote control to start pulling the winch cable back into the winch. This will cause the winch cable to tighten. Stop pressing the button when the cable is taut

Our Services

1. OEM service is available.

2. Fast producing time.

3. Inspect products one by one before shipping

4. Cheapest price for electric and hydraulic winches

5. Reply promptly in 24 hours.

If you have any questions, please contact with us directly. Compass winches are produced by With High Quality and Good Appearance. Welcome you can visit our Factory. For inquiry, please directly send mail to us.





electric winch 9500 lb,winch electric 12v,electric winch for sale

Suzhou DAO Material Technologies Co.,Ltd , https://www.dao-compass.com