Winter is approaching, and some people started to worry about the decoration when they entered the winter, because listening to many people said that winter is not a good time for decoration. But in fact, as long as you pay more attention, winter decoration is also desirable.
Dinghuan Wood Furniture Fengyasong Wood Furniture
1, wooden deformation
Solution: The main materials used in the decoration, especially the wood, need to be placed in a room with heating equipment for three to five days to evaporate the moisture that is produced due to temperature changes. This is done so that the moisture content of the wood is close to the level in the house, so that wooden deformation after the decoration can be avoided.
Before the winter renovation, in response to the influence of temperature and humidity on materials and processes, decoration companies should be equipped with humidification and heating equipment on site to adjust the construction site environment to suit the process requirements; meanwhile, materials such as wood, tiles, and paints should be used. The classification process was conducted and the construction was conducted after sealing for three days under constant temperature and humidity conditions. Three days of indoor and outdoor convection ventilation are also required after completion to observe carefully whether there is any accidental change.
2, wall cracking
Solution: Putty does not dry on the paint, the wall is easy to "sweat" or even a large area of ​​cracking, often window ventilation, the time is best selected between 10:00 to 4:00. The relatively high temperature during this period of time can prevent new batches of putty from freezing. After the putty was completely dry the first time, it was re-approved for the second time. After the second putty is completely dry, sand it carefully.
3, plaster line cracking
Solution: When the gypsum board is suspended, the moisture content of the wood keel must be controlled below 12%, and the keel must be firm and loose. This will prevent cracks in the gypsum board ceiling. Between the gypsum board and the joint between the gypsum board and the wall, leave a gap of about 0.5 cm. Use gypsum powder and latex to reconcile the joints. Then double stick the kraft paper and scrape the putty to prevent the plaster line. Cracking.
4, poor paint effect
Solution: In the event of strong winds and cool weather, it is not appropriate to carry out oil work. Because large wind and sand in winter, paint and paint are not dry, it is easy to attach dust, should pay attention to choose the weather without wind to brush, ensure the temperature of the coating application of the environment Not less than 5 degrees Celsius, the ambient temperature when the varnish is applied is not less than 8 degrees Celsius, and should be applied strictly according to the temperature in the product description. To prevent sand from falling on the paint surface, close the doors and windows.
5, improper joints
Solution: During the winter decoration, the seams of the doors and windows should not be too small, so as to avoid tight heat and tightness in the summer. When paving solid wood flooring, about 2mm of expansion joints should be left around. When furniture is made, about 0.1mm of interface seams must be left. The floor and wall joints should be bridged with floor layers and can be well handled. The disadvantages of excessive wall and floor gaps.
6, tiles off
Solution: Winter tiles and tiles must be soaked in water prior to pavement. Make sure the water is saturated. Only in this way, the phenomenon of hollowing and falling off will not occur due to the weak adhesion between cement and cement due to the suction water. In addition, no matter whether it is a wall tile or a floor tile, it must be transferred from the outdoor to the interior for 24 hours. Only when it is adapted to the indoor temperature can it be paved, so as to avoid emptying or falling off after construction.
Link: decoration acceptance is an important part to teach you the necessary magic and usage
Construction Acceptance Paint Interior Decorating Furniture Window Coatings Floor Tiles Tiles Tiles Tiles Floor Tiles Ld Tiles
Antique Powder Coatings with highly decorative finishes consisting of a base color with a vein pattern of a distinctly different color.
The base color is usually black, white or other colors.The vein pattern could be metallic (silver, gold or copper).
To preserve its decorative appearance, Clear Topcoat is highly recommended for indoor or outdoor use. More details ,please contact with 
APPLICATION SCHEDULE
- Applied by electrostatic spraying gun that can provide negative tension of 60-80 kV.
- Curing schedule : 180-200°C /10-15 minutes depending on the powder chemistry.
- Optimal film thickness : 80 -110 um
- The size of antique vein obtained depends on the coating thickness.
- Excessively thin or thick films will not give a satisfactory finish.
Antique Silver Powder Coating,Antique Powder Coating,Antique Gold Powder Coating,Antique Copper Powder Coating
Jinhu Color Powder Coating Co.,Ltd , http://www.powdercoatingscolor.com