[Rescue Tools] Gas Cutters

News Related Keywords: No tags.

【Overview】

The gas cutter operation method refers to a method of operating a gas cutter at a disaster site to cut a metal obstacle and rescue the trapped person to rescue or open a rescue channel.

Gas cutters use flammable gases (usually acetylene) and oxygen to cut metal equipment. Operators must have the required qualifications for practice.

(The name of the gas cutter and the operation of the operating line)

Article 61   The operating lines for the names and operation of each part of the gas cutter are shown in Figs. 15 and 16 .



【purpose】

The purpose of this article is to illustrate the name and operation of the various parts of the gas cutter.

(Importance enforcement precautions)

Article 62    In addition to the provisions of Article 4 , when using gas cutters, the following should also be noted.

First, it is forbidden to cut containers with residual gases and use them in a closed environment.

Second, it is forbidden to use in places where there are flammable gases, liquids, steam and dust.

Third, when the ignition, pay attention to stay away from the crowd.

Fourth, pay attention to check the ignition port is blocked, the cutting gun condition is normal.

5. The rubber tube should be placed in the opposite direction from Mars in the cutting operation.

Six, must be equipped with fire fighting equipment.

【purpose】

In addition to the provisions of Article 4 , this article also specifies other precautions when using a gas cutter. The commander must pay attention to the provisions of Article 5 .

[Details]

1. It is forbidden to cut containers with residual gases and use them in a confined environment. Pay attention to ventilation and ventilation when operating.

Second, it is forbidden to use in places where there are flammable gases, liquids, steam and dust. When cutting operations have to be carried out in such places, fireproof materials must be laid within the range where Mars may splash.

Third, use a dedicated igniter to ignite. When igniting, pay attention away from the crowd.

Fourth, when installing the pressure regulator, attention should be paid to removing the dust at the ignition port to prevent clogging and prevent the cutting gun from leaking.

5. Do not place the cutter in the ignition state. Since the Mars generated by cutting will cause the rubber tube to be damaged, be careful not to drag the rubber tube, and the hose cannot be placed in the same direction as the Mars splash generated by the cutting. In case of emergency, fire extinguishers or other fire-fighting measures should be deployed.

(Transport gas cutter)

Article 63    The passwords and instructions for transporting the gas cutter to the operating area are as follows.

First, the commander issued a "target''', handling" password.

Second, the commander heard One member of the "target''', handling" the password, left hand grip equipment boxes, according to the signal number two member of "start", with the number two member of the handling equipment boxes together to target location .

Third, the number two commander heard members of the "target''', handling" the password, the right hand grasp the handle of the equipment boxes, a "start" signal and handling the equipment boxes with the number one member to the target position.

【purpose】

This section specifies the passwords and essentials when transporting the gas cutter to the operating area.

[Details]

The passwords and instructions for transporting the gas cutter to the operating area are as follows.

order

1

2

commander

Issued a "target''', handling" password.

 

One member

Hear commander "target''', handling" password, equipment boxes left hand grip.

According to the "start" signal from the second member, the equipment box is transported to the target position together with the second member.

Second member

II members hear commander "target''', handling" the password, the right hand grasp the handle of the equipment boxes, a "start" signal.

Together with the first member, transport the equipment box to the target location.

Note

 

Avoid collision with the equipment box and be careful.

 

(Assembly and inspection of gas cutter)

Article 64    When assembling and inspecting the gas cutter, follow the following passwords and instructions.

First, the commander issued a "''' cutting, preparation equipment," the password, according to the "ready" signal number two members, issued a "check equipment" password.

Second, hearing One member of Commander "''' cutting equipment ready" after the password is selected to match the cutter and connected to the igniter, a "connection completed" signal, then the rubber hose connected to the torch A "good" signal was issued. After hearing the commander's "checking equipment" password, the appearance of the cutting gun was checked and a "checking completed" signal was issued.

Third, the number two commander heard members'''' cutting, preparation equipment "after the password, check the connection part is in place, to signal" ready "is; hear commander" inspection equipment "password after, Slowly and completely open the control valves of the cylinders. Check that the pressure signals “oxygen ́ ́ MPa , acetylene ́ ́ ́ MPa ”. Then check the status of the pressure regulator and the rubber hose connection and issue a “check completed” signal.

【purpose】

This section specifies the passwords and essentials when assembling and inspecting gas cutters.

[Details]

The passwords and methods for gas cutter assembly and inspection are summarized below.

order

1

2

3

commander

Issued a "''' cutting, preparation equipment" password.

 

According to the "Ready to complete" signal from the second officer, the "checking equipment" password is issued.

One member

One member of the commander after hearing "''' cutting, preparation equipment," the password, select the cutter matches the ignition and connect, issued a "well connected" signal.

Then connect the hose to the cutting gun and send a "good" signal.

After listening to the commander's "check equipment" password, look at the appearance of the cutting gun and send out a "check completed" signal.

Second member

After hearing II member of the commanders'''' cutting, preparation equipment, "the password, check the connection part is in place, a" ready. "

After hearing the commander's “check equipment” password, slowly open the control valves of each cylinder, check the pressure and send “Oxygen ́ ́ MPa , Acetylene ́ ́ ́ MPa ” signal, check the pressure regulator, rubber hose connection Part status, send out "check completed" signal.

Note

Make sure the ignitor is connected properly.

Special rubber hoses must be used and must not be bent or folded. When the rubber tube is damaged, it should be replaced in time, and no tape or other repairs are allowed.

Check the rubber hose for air leakage by applying soap liquid or putting the rubber hose into water.

 

(Ready to cut)

Article 65    When using a gas cutter to prepare for cutting, follow the following passwords and instructions.

First, the commander issued a "preparation for cutting" password after determining the cutting position.

After the first member heard the commander's “preparation for cutting” code, wear goggles and slowly turn on the acetylene pressure according to the “adjustment pressure, oxygen ́ ́ ́ MPa , acetylene ́ ́ MPa ” signal of the second member. Regulators and oxygen pressure regulators, igniting the igniter, adjust the tip flame to the optimum state and send a "ready to complete" signal.

The third and the second officer heard the commander's “preparation for cutting” password and issued the “adjustment pressure, oxygen ́ ́ ́ MPa , acetylene ́ ́ ́ MPa ” signal.

【purpose】

This section specifies the passwords and essentials when using gas cutters for cutting.

[Details]

Use the gas cutter to prepare the cut password and instructions as follows.

order

1

2

3

commander

After the cutting site is determined, a "preparation for cutting" password is issued.

 

 

One member

After hearing the commander's "preparation for cutting" password, wear goggles.

According to the "adjustment pressure, oxygen ́ ́ ́ MPa , acetylene ́ ́ MPa " signal of the second member , the acetylene pressure regulator and the oxygen pressure regulator are slightly turned on and ignited with a special igniter.

After igniting the igniter, the flame of the tip is adjusted to the best state and a "ready to complete" signal is issued.

Second member

After hearing the commander's “preparation for cutting” password, he issued the “adjust pressure, oxygen ́ ́ ́ MPa , acetylene ́ ́ ́ MPa ” signal.

 

 

Note

Wear goggles and protective gloves when cutting.

Prevents tempering (When the cutter is not operating properly, it will make a "click" sound, and then it will "click" and the flame of the ignition hole will turn off in an instant).

In order to prevent the fire in the rubber hose, it is necessary to open the oxygen inlet valve slightly, and then release a small amount of acetylene gas to ignite.

 

(cutting)

Article 66    When using a gas cutter to cut a job, follow the following passwords and instructions.

First, the commander issued a "start cutting" password, after confirming the operating conditions, issued a "stop cutting" password.

Second, the commander of the first member hears the "start cutting" password, heats the part to be cut, opens the oxygen switch for cutting, sends and discharges high-pressure oxygen to start the cutting operation, and after hearing the command of the commander to stop cutting, Stop the cutting operation, close the cutting oxygen regulator valve, cutter oxygen master switch and acetylene inlet regulator valve, and send out the "fire extinguished" signal.

【purpose】

This section specifies the passwords and methods for cutting operations.

[Details]

The passwords and methods for cutting jobs are organized in the following table.

order

1

2

3

commander

Issue a "Start Cut" password.

Check the operation status.

The "stop cutting" password is issued after confirming the operating state.

One member

After hearing the commander's "start cutting" password, heat the part to be cut, turn on the cutting oxygen switch, and send and discharge high-pressure oxygen to start the cutting operation.

 

After hearing the command of “stop cutting” by the commander, stop the cutting operation, close the cutting oxygen regulating valve, the cutter oxygen main switch and the acetylene air inlet regulating valve, and send out the “fire extinguished” signal.

Note

The object of the cutting work is steel. The amount of oxygen used for cutting is increased or decreased depending on the thickness of the material being cut. For an empty bottle that has run out of gas, the pressure regulator must be closed.

 

The cutting oxygen regulating valve, oxygen inlet regulating valve, acetylene inlet regulating valve and oxygen main switch are closed in sequence.

(finishing equipment)

Article 67    When you clean up the gas cutter, follow the following passwords and instructions.

First, the commander sends out the password for "shut up".

The first and second members vented the gas in the cutting gun according to the “closed” signal of the second member and returned the equipment to the equipment box together with the second member. The equipment box was transported to its original position and returned to the operating line for standby.

After the third and second members heard the command of the commander to “close”, they closed the control valve of the acetylene gas cylinder and the oxygen gas cylinder and issued a “Closed Completed” signal. Together with the No.1 member, the equipment was returned to the equipment box. After the equipment box is transported to its original position, it returns to the operating line and stands by.

【purpose】

This article specifies the passwords and essentials for cleaning up the gas cutter.

[Details]

The passwords and methods for cleaning up the gas cutters are summarized in the table below.

order

1

2

3

commander

Send a "Close" password.

Earth Anchor

15 inch length with 3 inch width helix auger earth anchor. Package quantity: 1pc
Powder coated red color. Weld eye ring for installation and tie off. Firmly welded helix.
Easy installation by hand or machine
Screw into the ground to guy down tents, canopies, storage buildings, fencing, playground equipment, trees, as well as more other guying uses.

Earth Anchor,Earth Screw Anchor,Paint Earth Anchor,Earth Screw

Hebei Honde Plastic & Metal Co., Ltd. , https://www.foundation-system.com