After returning home after a busy day, my favorite is to sit quietly in the tub and soak in a hot bath. The bathtub is closely connected with people's daily life. So what are the precautions for bath installation? In this issue, Xiao Bian used the Kohler massage bathtub as an example to introduce the precautions for the installation of Kohler massage bathtubs.
Kohler massage bathtub installation
Kohler has a history of more than 130 years and is one of the most familiar brands in the world for consumers. Its most admired concept of home life is "elegant life", giving people a sense of nobleness.
The first step: test whether the water leaks.
Place the bathtub before the first water accessories, do water for 24 hours to see if the bathtub is leaking, pay special attention to the overflow. It's very difficult to close the water in 24 hours. Outside the bathroom, pour two buckets of water and try a good bathtub to get water. This is convenient.
At the time of actual installation, the bathtub was directly lifted into the bathroom and placed in the water. Since the width of the bathtub was just the same as the width of the bathtub when the water was changed, the size of the bathtub and the mixing of water was not correct. Note that the center point of the bathtub should be facing the center of the mixing water, otherwise it will be very difficult to see if the mixing faucet is installed in the future.
Bathtub installation considerations
After the bathtub is lifted into the bathroom, it starts to put on and off the water fittings, fills the bathtub with water, closes the water, and checks for leaks. When the water flows over the overflow, the water in the bathtub flows out of the overflow. This time, go Touch the back of the spill to see if water leaks out from here. After the overflow test is passed, the next step is to check the sealing of the sewage, and to select the method of standing and observe the tightness of the sewage.
The second step: leveling the bathtub.
When placing the bathtub, take care that the other end of the water outlet is slightly higher than the end of the drain so that the sewage will not be discharged in the future. This depends on the circumstances. Observe that the bottom of the bathtub had a slope for draining water, level the bathtub on the four sides, and put a water test. As expected, the water quickly drained. The bathtub visually maintains a level of beauty without affecting the effect of drainage
The third step: fill sand.
Although the cast-iron bathtub is strong, its thermal conductivity is very fast. It should be used in Zhonghesha and it should be firmly laid on the bottom of the bathtub. Bricklayers also recommend the use of foam. Considering that foam is not as mobile as sand, it is ideal to fill all the gaps. In the process of filling sand, how to make sand not leak into the sewage pipe is a problem to be solved.
After all the placement work was completed, the water release test was performed again (this step was mainly to ensure that the backside of the bathtub did not leak water). After confirming it was correct, it waited for the bricklayer to lay the skirt.
Step 4: Leave the access port.
A 300mm wide 400mm hole is left at the water outlet, and one hole is cut to size. The board is made of water-repellent and anticorrosive wood (thickness 40mm) according to the size. The number of bricks and the number of rows arranged on the board are 903. The glue sticks the brick to the board. Extend the edge of the brick with a sealant and insert it on the box. This is to facilitate the overhaul of the bathtub drainage system in the future. In the bathtub skirt, for aesthetic considerations, all set aside 600 heights, give up other materials such as mosaics, bath skirts and the same brick under the wall brick, so to do, under the wall tiles, floor tiles, bath skirts are all One color, one material, very beautiful.
Step 5: Tiling
Bathtub skirt tiles do not need to scratch the hair, build a red brick table, a layer of cement mortar on the surface, and then wait two days and then tiling can, tiling is very troublesome, due to the slope of the ground to stay, and the bathtub It's flat, so every big brick must be polished to different sizes. It's not possible to polish a lot at a time, it's easy to grind, and it's repeated. The top of the brick is to be inserted under the round edge of the bathtub so that it does not form an angle.
Reminder: For more information, please pay attention to the information on this website , or you can visit our offline experience directly.
Bathtub Bathroom Bathroom Bathroom Tap Cement Home Red Brick
Electrolytic copper is a non-ferrous metal with very close relationship with human beings. It is widely used in electric, light industry, machinery manufacturing, construction industry, national defense industry and other fields, second only to aluminum in the consumption of non-ferrous metal materials in our country.
Copper is the most widely used and widely used in the electrical and electronics industries, accounting for more than half of the total consumption. For a variety of cables and wires, motor and transformer windings, switches and printed circuit boards.
Used in the manufacture of machinery and transport vehicles for the manufacture of industrial valves and fittings, gauges, sliding bearings, molds, heat exchangers and pumps.
In the chemical industry is widely used in the manufacture of vacuum, distillation pots, brewing pots.
In the defense industry for the manufacture of bullets, shells, guns and other parts, each producing 1,000,000 rounds of ammunition, the need for copper 13-14 tons.
In the construction industry, used as a variety of pipes, pipe fittings, decorative devices.
Copper Content Of 99.99%
Copper Content Of 99.99%,High Copper Content,Copper Content Enameled Copper,99.99% Copper Content
Ningxia Tongji International Trade Co.,Ltd. , https://www.tongjiinternational.com