>>>Links: The specific process of laying the floor heating
After people have installed floor heating or cooling fins, they will be charged for the use of the cost. What is the monthly cost?
The answer is: Does the cost depend on your house, energy-efficient or non-energy-efficient? What is the degree of energy saving?
However, it is also a waste of money for office workers who usually have no one at home during the day.
Yes, based on actual experience and theoretical calculations, regardless of whether someone is at home, the floor is warmer and warmer than people are warm to the ground. The method of warming people up is much more economical, because when you first start heating, first the interior walls of the room The body begins to absorb heat, which is quite large. When the wall absorbs heat almost, the heat dissipation is only needed to supplement the heat of the heat-consuming part and it can reach equilibrium. At this time, the required heat is much smaller.
A more economical approach can be such that when a person walks, the water temperature or room temperature is controlled to 13-15 degrees. After the person returns home, the indoor temperature is controlled to 18-20 degrees, and the temperature is also very fast. In the first 10 minutes, it will reach 18-20, but when the cold starts again, the 100-square-foot house will be at least 2 hours, and it will consume more energy.
Of course, if the room will be empty for more than 3 days, that is, if there is a few days when heating will not be used, it is recommended that the heating be turned off.
Heating costs in addition to the above major factors, there are problems with the use of habits, such as: open floor heating, but long open windows, or, some people like the indoor temperature above 22 degrees (usually more comfortable temperature should be 18 - 20 degrees), which is the reason for the increase in heating costs.
It is worth mentioning that when the room is not heated, that is, the indoor temperature is basically close to the outdoor temperature room, such as the outdoor temperature of 0 degrees, the indoor temperature of 5 degrees, so that the wall temperature of the house will also be 5 degrees Around, when the heating is started, first the interior walls of the room begin to absorb heat and reach a temperature that is basically close to the design (for example, a design temperature of 20 degrees), at about 15-18 degrees, and the amount of heat required at that time is quite large. After the wall has absorbed heat, the amount of heat needed to replenish the heat-consuming part of the wall can reach equilibrium. At this time, the amount of heat needed is much smaller.
Therefore, the heating cost depends on whether your house is energy-efficient. In addition, we also think that when I go out, I turn off the heating, and the wall starts to cool down, return home, and turn on heating again. This wastes the wall. The heat is very large, causing an increase in the cost of one month. This habit derives from our understanding of air-conditioning. Air-conditioning relies on the wind to blow out the air. The place where it is blown is relatively cold. However, after turning off the air-conditioning, it starts after a few minutes. It is as cold as the wall is not heated. This is the air conditioner. The same is true in the bathroom bath. This kind of heating is not comfortable.
First of all, it is said that the principle of heating: a house that has been built, when it is at a high indoor temperature, such as 20 degrees, when the outdoor temperature is 0 degrees, the house itself has a certain amount of heat, and the room has been heated ( Geothermal, heat sinks, and geothermal) have a certain amount of heat dissipation. If the amount of heat to be dissipated exceeds the heat consumption of the house, the temperature will be fixed at the designed temperature. If the heat dissipation is less than the heat of the room, the indoor temperature will be Below the designed temperature.
Therefore, the heating cost depends on whether your house is energy-efficient. In addition, we also think that when I go out, I turn off the heating, and the wall starts to cool down, return home, and turn on heating again. This wastes the wall. The heat is very large, causing an increase in the cost of one month. In other words, regardless of whether there are people at home or not, they have to open up the heating?
Buy materials house room window bathroom design
Flexible Flap Disc
Flexible Flap Disc is suitable for polishing of stainless steel, metal, metallurgy, automobile, wood, marble and other industries. It is especially suitable for the processing of stainless steel and can replace the resin-shaped grinding wheel. It has strong elasticity, high tensile and bending strength, good self-sharpening, high grinding rate, and low noise. It is suitable for welding seams in the box. Polishing of the edges.
The related abrasive products we can supply is Flap Disc Adhesive , Bonded Abrasives , Flap Wheels , Abrasive Sanding Disc, and Abrasive Machine such as Flap Disc Making Machine,Abrasive Belt Making Machine, Flap Wheel Machine ,Sanding Disc Machine, if you have any needs about abrasive tools, please kindly feel free to contact us.
According to the type of abrasive particles: ceramic alumina VS zirconium corundum VS alumina
According to the type of abrasive selected, the flap disc can be divided into three types: ceramic alumina, zirconium corundum and alumina.
Because ceramic alumina itself has many crystals, it has good self-sharpening, relatively neat edges, good heat dissipation, and long service life. Therefore, ceramic alumina louvers are mainly used for the grinding of stainless steel, aluminum and other hard metals.
Zirconium corundum itself is a polycrystalline crystal, with fast cutting speed, good self-sharpening, and strong resistance to high pressure and high temperature. Therefore, zirconium corundum louver blades have strong cutting ability and long service life.
Alumina: single crystal, the cutting ability begins to decline at the beginning of grinding, and the abrasive grains are not easy to break, so the alumina flap disc is suitable for the processing of common metals.
Flexible Flap Wheels Disc,Abrasive Flexible Flap Disc,korea flap disc,flower flap disc,Flexible Flap Disc
Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.abrasive-jd.com