1. Firstly, the total area (or number of blocks) of the anti-static floor required for computer room construction and the number of various accessories (standard ratio 1:3.5, 1:5.5) need to be accurately established, and a margin is left to avoid wastage. Or shortage.
2. To fully understand the variety and quality of anti-static floor produced by the manufacturer, as well as various technical performance indicators. The technical performance of anti-static flooring mainly refers to its mechanical and electrical properties. The mechanical properties mainly consider its bearing capacity and wear resistance. Place the whole piece of anti-static floor on the spliced ​​truss beam. After leveling the anti-static floor, the load-bearing capacity should reach a uniform load greater than 1000 kg/m2, and the concentrated load on any part of the anti-static floor should be greater than 300 kg. For a 6-cm load point with a load of 300 kg, the deflection should be less than 2 mm and there should be no permanent deformation. Adjustable support should be able to withstand more than 1000kg of vertical load, and the board should have a certain degree of abrasion resistance. The electrical properties are mainly system resistance and surface resistance. The system resistance should be 106Ω-109Ω. When the temperature is 21±1.5°C and the relative humidity is 30%, the static voltage of the antistatic floor should be lower than 2500V, and the surface resistance value should be 106Ω-109Ω.
3. The load of the anti-static floor shall be determined based on the weight of the heaviest equipment among all equipments in the equipment room, so as to prevent the permanent deformation or damage of the floor caused by the overweight of some equipments.
4, anti-static floor is subject to changes in external environmental conditions, that is, not because of the external environment temperature is too high, too low, there is significant expansion, that is, when the room temperature is slightly higher, the anti-static floor expansion, can not be removed and replaced When the temperature is low, the anti-static floor shrinks, creating a loose feeling. The amount of shrinkage of the antistatic floor affected by the environment should be less than 0.5mm, and the deflection of the board surface should be less than 0.25mm.
5. The surface of anti-static floor should not be reflective, slippery, corrosion-resistant, dust-free, dust-free, and easy to clean.
2. To fully understand the variety and quality of anti-static floor produced by the manufacturer, as well as various technical performance indicators. The technical performance of anti-static flooring mainly refers to its mechanical and electrical properties. The mechanical properties mainly consider its bearing capacity and wear resistance. Place the whole piece of anti-static floor on the spliced ​​truss beam. After leveling the anti-static floor, the load-bearing capacity should reach a uniform load greater than 1000 kg/m2, and the concentrated load on any part of the anti-static floor should be greater than 300 kg. For a 6-cm load point with a load of 300 kg, the deflection should be less than 2 mm and there should be no permanent deformation. Adjustable support should be able to withstand more than 1000kg of vertical load, and the board should have a certain degree of abrasion resistance. The electrical properties are mainly system resistance and surface resistance. The system resistance should be 106Ω-109Ω. When the temperature is 21±1.5°C and the relative humidity is 30%, the static voltage of the antistatic floor should be lower than 2500V, and the surface resistance value should be 106Ω-109Ω.
3. The load of the anti-static floor shall be determined based on the weight of the heaviest equipment among all equipments in the equipment room, so as to prevent the permanent deformation or damage of the floor caused by the overweight of some equipments.
4, anti-static floor is subject to changes in external environmental conditions, that is, not because of the external environment temperature is too high, too low, there is significant expansion, that is, when the room temperature is slightly higher, the anti-static floor expansion, can not be removed and replaced When the temperature is low, the anti-static floor shrinks, creating a loose feeling. The amount of shrinkage of the antistatic floor affected by the environment should be less than 0.5mm, and the deflection of the board surface should be less than 0.25mm.
5. The surface of anti-static floor should not be reflective, slippery, corrosion-resistant, dust-free, dust-free, and easy to clean.
County Shengxin Metal Products Co., Limited , http://www.hbwire-mesh.com