The toilet is an essential part of our daily life. Generally, we need to choose a toilet when we are doing renovations. We are the most important places in terms of quality and size. However, when measuring the size of the toilet pit, most people are not very likely to do so, so let's take a look at the toilet pit distance and the distance from the toilet pit. 
What is the distance from the toilet bowl?
1. The distance between the pit and the toilet is very important. It refers to the distance from the center of the toilet's sewer to the wall. Then the opening size of the toilet opening in the toilet. Before a suitable toilet, we must first select the appropriate pit distance, the general size will be 300mm, 350mm, 400mm, 450mm and so on. 
2, in the determination of the bathroom toilet pit distance, we also have to make a decision based on our home bathroom area, each family decoration bathroom area will be different, the location of the natural installation of the toilet is also different, pit distance also need to be based on The bathroom design determines the pit distance. In actual operation, reserve 20mm, 20mm is the distance of the reserved wall tiles, then the actual distance from the center line of the toilet outlet to the wall is 320mm or 420mm, the actual error is 10mm normal, and the premise can be installed normally.
Toilet pit distance measurement techniques
1. When measuring the distance between the toilet pits, we must first clean the sewage pipes, and then conduct self-love inspections to ensure that there is no debris. At the imprint, drill a hole with a diameter of 20mm and a depth of 60mm. Insert a bolt with a diameter of 10mm into the hole. After the test, remove the toilet. Put a putty around the outlet pipe on the left side and align the four bolt holes with the bolt. Flatten and align, bolt the rubber pad, and tighten the nut. 
2, we can learn to measure the skill of the toilet pit distance, so that we can more easily know how we want to design the toilet, and then draw a horizontal line 800mm from the ground in the middle of the toilet, how to mark the location of the two holes on the back of the toilet tank A hole with a diameter of 30 mm and a depth of 70 mm is drilled at the cathode. Insert a bolt with a diameter of 10mm and a length of 100mm into the hole and screw it tightly with concrete. The tank will be hung on the bolt and be leveled and aligned. To align with the center of the toilet, padded the rubber pad, and tighten the nut until it is tight and moderate. 
3, and then to carry water tank water elbow, and then remove the water outlet and the toilet nut nut, the upper end into the water tank under the water inlet, the lower end into the toilet water inlet, and then push the pad to the outlet screw Nut on. When using the eight-word door to link the Sheung Shui, it is necessary to first measure the size of the water tank's slopping door from the upper nozzle. Put brass or plastic pipe and two pipes of oil-wrapped asbestos rope or lead-oil twine on the copper pipe or plastic pipe, and insert them into the drain door and the eight-word door respectively, and tighten the nut.
Summary: The general information about the distance between the pits of the toilet and the information about the measuring technique of the toilet pit is introduced here. I hope this helps everyone. If there is something that you do not understand, you can pay attention to more content. If you want to learn more about building materials, please continue to pay attention to our website.
stainless steel commercial flat washers are used under bolt heads or nuts to increase the bearing surface area, or to offer protection so that the nut or bolt can be rotated without distortion of the bearing surface. Flat washers are also used to give tightness to a joint, to prevent leakage, and especially to distribute pressure under the head of a bolt or nut. Dimensional specifications are governed by ASME B18.21.1. Commercial flat washers generally have a larger outer diameter than SAE (Society of Automotive Engineers) flat washers, and can be utilized in nearly any application. stainless steel fasteners are commonly used in applications that require general atmospheric corrosion resist ance, such as chemical and food processing equipment. Stainless steel has a higher corrosion resistance than carbon steel.
Stainless Steel Washer,Ss Washer,Stainless Steel Square Washers,Black Metal Washers
Taizhou Hongchuang Hardware Co., Ltd. , https://www.jstaizhouhongchuang.com