1, the basic requirements of system installation and design
(1) The installation design should be based on the protection requirements of the area to be protected, and select the appropriate detector type, model, etc.
(2) According to the effective protection area of ​​the detector and the on-site environment, the installation position, angle and height of the detector are determined, and the detector is required to be installed in a concealed position as far as possible under the protection requirements.
(3) Traces should be hidden as much as possible to avoid damage. If the open line should be protected by rods or plastic pipes to prevent damage by rodents (such as rodents).
(4) The construction drawings shall indicate the model specifications of the detectors and optical cable of each zone, and indicate the use of the colored lines in the cable.
(5) The construction drawings shall be kept for record, which is convenient for system maintenance.
2, system installation and debugging
(1) Installation requirements of infrared detectors
When installing, attention should be paid to the angle and height between the detector and the horizontal plane, which has a great influence on the protection area.
Should avoid cold and heat sources, such as hot and cold air outlets, air conditioning outlets, heaters, air conditioners and so on.
The detector should be able to look directly at the protected area and there should be no obstacles.
The detector avoids direct access to doors and windows.
In order to ensure the antenna transmission effect, please pull the transmitting antenna completely.
(2) Mounting of magnetic switch
Door magnetic switch should be based on the minimum angle to determine the installation position, the distance between the magnetic block and the magnetic switch can not exceed 10 mm.
In order to ensure the antenna transmission effect, please pull the transmitting antenna completely.
(3) Installation of alarm host
The main alarm should be installed in the concealed position, but it should be noted that the position of the microphone and built-in speaker on the front panel of the host should not be covered to ensure that the monitor sensitivity and alarm sound level are not affected.
The alarm host is non-explosion-proof and can not be directly used in Class I, II, and III hazardous locations (ie places with a certain concentration of flammable, explosive vapor, dust, and fiber), otherwise there may be danger!
The alarm host should be near the TV, air conditioner, computer, microwave oven and other strong electromagnetic radiation equipment, so as not to affect the antenna receiving effect.
In order to ensure the reliable operation of the system, it is recommended to configure the backup battery. If there are frequent outages or power outages in the area of ​​use, it is recommended to configure a backup power supply with a larger capacity.
In order to ensure the antenna receiving effect, please pull the receiving antenna completely.
(1) The installation design should be based on the protection requirements of the area to be protected, and select the appropriate detector type, model, etc.
(2) According to the effective protection area of ​​the detector and the on-site environment, the installation position, angle and height of the detector are determined, and the detector is required to be installed in a concealed position as far as possible under the protection requirements.
(3) Traces should be hidden as much as possible to avoid damage. If the open line should be protected by rods or plastic pipes to prevent damage by rodents (such as rodents).
(4) The construction drawings shall indicate the model specifications of the detectors and optical cable of each zone, and indicate the use of the colored lines in the cable.
(5) The construction drawings shall be kept for record, which is convenient for system maintenance.
2, system installation and debugging
(1) Installation requirements of infrared detectors
When installing, attention should be paid to the angle and height between the detector and the horizontal plane, which has a great influence on the protection area.
Should avoid cold and heat sources, such as hot and cold air outlets, air conditioning outlets, heaters, air conditioners and so on.
The detector should be able to look directly at the protected area and there should be no obstacles.
The detector avoids direct access to doors and windows.
In order to ensure the antenna transmission effect, please pull the transmitting antenna completely.
(2) Mounting of magnetic switch
Door magnetic switch should be based on the minimum angle to determine the installation position, the distance between the magnetic block and the magnetic switch can not exceed 10 mm.
In order to ensure the antenna transmission effect, please pull the transmitting antenna completely.
(3) Installation of alarm host
The main alarm should be installed in the concealed position, but it should be noted that the position of the microphone and built-in speaker on the front panel of the host should not be covered to ensure that the monitor sensitivity and alarm sound level are not affected.
The alarm host is non-explosion-proof and can not be directly used in Class I, II, and III hazardous locations (ie places with a certain concentration of flammable, explosive vapor, dust, and fiber), otherwise there may be danger!
The alarm host should be near the TV, air conditioner, computer, microwave oven and other strong electromagnetic radiation equipment, so as not to affect the antenna receiving effect.
In order to ensure the reliable operation of the system, it is recommended to configure the backup battery. If there are frequent outages or power outages in the area of ​​use, it is recommended to configure a backup power supply with a larger capacity.
In order to ensure the antenna receiving effect, please pull the receiving antenna completely.
Lockout tagout stations ensure proper storage of lockout devices for easy accessibility. They provide a great way to organize and centralize lockout activity. These stations are sold without lockout tagout (LOTO) equipment included, making them a cost effective way to supplement your current LOTO equipment or customize your own kit.
Lockout Station,Safety Lockout Station,Lock Out Station,Lockout Tagout Station
Lockey Safety Products Co., Ltd. , https://www.lotolockey.com