For home decoration, its hydropower project is one of the five major projects, so whether it is hydropower construction or water and electricity acceptance are particularly important. In order to ensure that there will be no hydropower problems in the future, do not ignore hydropower acceptance when checking and accepting. So, what are the acceptance criteria for hydropower ? The following is a detailed explanation for everyone by Xiaobian.
What are the standards of water acceptance?
1. What are the acceptance criteria for hydropower? First of all, we must first carry out the acceptance of the waterway. In the acceptance of the waterway, we must first check each faucet to see if there is leakage, seepage, and blockage of the water pipe. Then turn on the faucet again to make the water flow as large as possible, see how the water quality is, and if there is a rusting valve, look at the water pressure and drain speed.
2. Check whether the water meter will go empty, the valve is off the wire, the valve is not closed tightly, and the connector is dripping.
3. Look at the water meter again and record that the meter data is the responsibility of the developer.
4. Check whether the water in the toilet bowl is unobstructed, because it is feared that the garbage will be blocked or the flushing water will not be smooth during the decoration.
5. In the bathroom to do a waterproof test, observe whether the leveling layer 30mm and the shower wall 1800mm are waterproof. Then close the water experiment, and go downstairs after 24 hours to see if there is a leak.
6. Check whether the installation of the floor drain meets the requirements, no leakage, no flooding, and the ground and floor drain joints are smooth and smooth so that they meet the requirements.
7. If you buy a penthouse, check the water resistance on the top of each room to see if there is any trace of rain.
What are the standards of circuit acceptance?
1. What are the acceptance criteria for water and electricity? The circuit is now undergoing acceptance. Check to see if there is electricity on the outlet panel, and if the switches, sockets, and mains breakers in each room are normal. At this time, the indicator light of the socket switch in the main switch box can be turned off, and it is tested several times to observe whether the switch, the socket and the wiring are normal.
2. We can also turn off the main gate to see if the room is completely in a power-off condition.
3. Then check whether the meter can operate normally. If it is too fast or too slow, repair it and then record the data of the meter. This part of the electricity fee is not issued by the owner.
4. Then check the socket to see if it is well grounded and there is no grounding device installed. See if the socket is loose or not plugged in.
5. Then check whether the number of circuits in the house meets the standard. In general, the number of circuits should not be less than 5. This is for the purpose of electricity safety.
6. Check whether the switch in the switch box is firmly installed. If it is loose, replace it or fasten it. There will be problems such as poor contact and fire, and there will be security risks.
7. Check whether the emergency call button and video intercom work normally, and if the doorbell of the entrance door is ringing.
8. To ensure the safety of children at home, safety devices must be installed on sockets 30 cm above the ground.
9. In order to use electricity safely, the socket of the bathroom should be a moisture-proof socket, and the lighting of the bathroom should be a safe socket of a magnetic port.
The article concludes: In order to protect the safety of electricity for the family, and to avoid leakage and water seepage problems in the future, the water and electricity acceptance must be careful and do not ignore the acceptance of hydropower. In the acceptance of hydropower, we can refer to the above- mentioned hydropower acceptance standards , hoping that the above content can help everyone.
Cree LED Grow Light can save about 30% cost in the application,mainly lie in LED package cost,light engine production costs and the secondary light distributioncosts, which is great significance for applications and promotion of semiconductor lighting. We could also DIY the led ratio(wavelength ratio) which imitate the natural sun spectrum to help your plants grow in a very natural type of atmosphere, Absolutely, we are the very original and professional OEM/ODM factory, our Cree LED Grow Light have the great cost performance with the new integration technology being used for mass production, partners around the world keep telling us how amazed at the increase in output and the decrease in the energy bill.
Applications
Our professional full spectrum Cree LED grow light are suitable for all the indoor plants and good for seeding, growth,flowering and fruiting stages of plants, increasing the harvest and Saving energy.
Key Features
Plug with listed certificate safe to use.
Item Display
The Plug you can choose
Full Spectrum Cree LED Grow Light PAR Value
Our Ageing Test
Package
Warnings:
1.lndoor use only.
2.To avoid being damaged,do not use water or drip irrigation while using.
3.Sunshine lighting time should be 12-18 hours.
4.While irradiating the plants,the height of led grow lamp is not less than 10 inches,low height will cause the destruction of plants.
5.Highly hang the lamp will weaken the energy and affect the growth cycle of the plants, so the lamp should not be hung too high.
6.While taking care of the plants, please spray the leaves and branches 2-3 times everyday,to ensure the the plants do not wrinkle a wither, and have no phenomenon of few fruit, and hard pericarp.
Warmly welcome to Visit our Factrory when you come to China.
CREE Chips LED Grow Light,CREE LED Grow Light,CREE Grow Light,CREE COB LED Grow Light
Shenzhen Phlizon Technology Co.,Ltd. , https://www.szledaquariumlighting.com