Grease gun is a hand tool for filling grease in mechanical equipment. It can be equipped with an iron gun bar (iron gun head) or a hose (flat gun head) filling nozzle. You can use the iron gun (iron head) for the convenient refueling position and in a spacious space. To hide the refueling position, you must use a hose (flat gun head) to refuel at the corners. Let me introduce to you how to use the grease gun.
Â
　　 How to use the grease gun
Â
Bulk butter
1. Unscrew the oil gun head to separate the oil gun head from the barrel.
2. Immerse the opening of the barrel into the barrel of butter about 30 mm deep. Hold the barrel with one hand and pull the follower handle at the rear of the barrel to draw the butter into the barrel.
3. Install the oil gun head, press and hold the locking piece at the rear of the barrel and push the driven handle into the barrel.
Note: Air is easy to be left in the oil-filled gun, which can not produce butter. At this time, the follower handle of the tail of the barrel should be pulled to the end, then press the exhaust hole with one hand and press the locking piece at the end of the barrel. At the same time, the follower handle is pushed into the barrel to expel the air in the gun. This method is referred to as the exhaust method. Another exhaust method is to push the driven handle a few times in the barrel of the gun when there is no exhaust valve on the grease gun, then loosen the tip of the gun slightly and then tighten the head.
Butter cartridge or butter
1. Unscrew the oil gun head to separate the oil gun head from the barrel.
2. Pull the follower handle to the end, then unscrew the lid of the oil cartridge or barrel of butter to the direction of the barrel and put the oil bomb into the barrel to tear off the other end of the seal.
3. Don't turn the gun head too tightly. Press the locking piece at the tail of the gun head and push the follower handle into the barrel without load.The follower handle will be pulled to the bottom and pushed back to the original place to exhaust. If there is an exhaust valve, you can tighten the gun head first and then press the exhaust valve a few times while operating the driven handle to exhaust.
4. Tightening the gun head will push the handle into the barrel.
Note: If the oil bomb is in rubber packaging, commonly known as a butter bomb, when the butter bomb is screwed to the screw hole on the gun head, there is no need to operate the exhaust action of the driven handle. If the oil bomb is a barrel of butter, you must pay attention to the barrel The rubber bowl inside should be able to enter and has entered the grease barrel of the barrel and the edge of the grease barrel is not deformed or damaged. Otherwise, the grease gun will not be able to hit the butter and will not work.
Pumping butter
1. Connect the oil receiving nozzle on the tip of the grease gun to the oil filling nozzle of the pump.
2. Hold the grease gun and operate the pump handle. When the butter is injected, the driven handle will automatically move backwards until it can no longer move, indicating that the oil is full.
3. Gently disengage the oil pump connector and press the locking piece at the rear of the barrel to push the driven handle into the barrel.
Note: Remember to take out the oil bullets that may be left in the barrel before filling.
The above is to introduce the use of grease gun to friends. When using a grease gun, it should be handled lightly to prevent the barrel from deforming under the action of external force and causing the rubber bowl in the barrel to not work properly. When using butter, it is best to use good quality and no impurities to avoid the failure caused by poor quality butter.
There are a large number of Excavator Final Drive Travel Motor assemblies in stock, which can be sold in lots. We have professional technicians, who can control the quality of each travel motor assembly, disassemble the travel reducer, and check the internal gear. The travel motor can measure the travel pressure with a professional technical oil pump to ensure that there is no problem with the travel pressure before it is delivered to you. You will receive a satisfactory travel assembly, It can be loaded and used normally without debugging. The price is especially cheap.
We provide good power in high-quality and progress,merchandising,revenue and internet marketing and operation for Hyundai Final Drive Hyundai Travel Motor, Hyundai Travel Motor,Hyundai Travel Gearbox,Hyundai Final Drive Spare Parts,Hyundai Drive Parts,Hyundai Motor . Currently, we are wanting ahead to even bigger cooperation with abroad customers according to mutual positive aspects. Be sure to sense free to contact us for more details. The product will supply to all over the world, such as Europe, America, Australia,Honduras , Madras ,Paris , Nepal .We will supply much better products with diversified designs and professional services. We sincerely welcome friends from over the world to visit our company and cooperate with us on the basis of long-term and mutual benefits.
Hyundai Final Drive,Hyundai Final Drive Assy,Hyundai Travel Motor,Hyundai Travel Gearbox,We are sure to have the Hyundai final drive or travel motor you need.long-standing final drive provider.and 15 month warranty on final drives.
Hyundai Final Drive,Hyundai Final Drive Assy,Hyundai Travel Motor,Hyundai Travel Gearbox,Hyundai Final Drive Spare Parts,Hyundai Drive Parts,Hyundai Motor
Jining Juheng Hydraulic Machinery Co., Ltd. , https://www.sdjuhengmachine.com